8/8/2023 0 Comments I stat clew updateWhen power is supplied to the USB Downloader/ Recharger, it will look as it did before power was supplied. STEP 1.4 Connect the power supply to the VetScan i-stat 1 USB Downloader/Recharger or Serial Downloader and then to the wall outlet or power strip. Contact Abaxis Technical Support at for assistance. If not installed, navigate to and download. If using the USB Downloader/Recharger, make sure the Driver has been installed. If using a Serial Downloader, connect the Serial Downloader to the 9-pin serial port on the back of the computer with the 9-pin null modem serial cable as shown. If using a USB Downloader/Recharger, connect the USB Downloader/Recharger to the USB port on the back of the computer with the USB cable as shown. Connecting/Setting Up Equipment i-stat 1 JammLite Utility STEP 1.3 Connect Downloader to a computer. If you have disposable batteries, replace with new batteries if voltage is below 7.5. If you have rechargeable batteries, charge your analyzer until it has at least 7.5 volts. If the computer does not have one, contact Abaxis Technical Support at a b c d f e g 3 Instructions for Updating i-stat SoftwareĤ STEP 1.2 Ensure your VetScan i-stat 1 has at least 7.5 volts of battery power. 2 Instructions for Updating i-stat Softwareģ 1 Update with JammLite Utility (web or CD-ROM) Follow these steps to update with JammLite Utility Gather Equipment for JammLite Utility i-stat 1 JammLite Utility STEP 1.1 Before starting the process, make sure all the required equipment is available: Computer with: Windows 2000 and above USB port for use with the USB Downloader/Recharger or a 9-pin serial port if using a Serial Downloader Access to: or CD-ROM drive (if using software CD) VetScan i-stat1 System Equipment (see picture below): USB Downloader/Recharger a and USB cable supplied e or Serial Downloader b and 9-pin null modem serial cable f Downloader Power Supply c VetScan i-stat 1 Analyzer d If necessary Current JAMS/CLEW software CD g When using serial downloader, a computer with a traditional port 9-pin serial port or a serial port adapter is required. This method is a good choice after the first analyzer has been updated via the JammLite Utility and other analyzers that need updating are not near the PC that was used to run the JammLite Utility. 1 Update with JammLite Utility (web or CD-ROM) or 2 Update with the Process Choosing the Best i-stat 1 Software Update Method JammLite Utility If you have all the necessary equipment (see page 3), it s best to update your i-stat 1 analyzer(s) via the JammLite Utility if they are readily available and near the PC you will use to run JammLite. This process is noted in the diagram below Gather equipment for JammLite Utility Connect/set up equipment Load JAMS/CLEW Update i-stat 1 analyzer Verify software update 1 Instructions for Updating i-stat SoftwareĢ Once the first i-stat 1 analyzer has been updated using the JammLite Utility, additional i-stat 1 analyzers may be updated the same way or by using the method. JammLite Utility (Software update) Process Overview Whether updating one or more i-stat 1 analyzers, the JammLite Utility procedure must be used to update the first i-stat 1 analyzer. The new JAMS application software allows the i-stat 1 analyzer to recognize any newly launched cartridge types and to perform any newly launched features. The new CLEW software re-establishes these standardization values and incorporates refinements to the internal quality monitoring system. Each software update includes both CLEW software and JAMS application software and is delivered twice per year (May and November) available on the Abaxis website or via a CD-ROM. These updates are equivalent to manually adjusting calibration on a traditional laboratory analyzer. Due to the continuous manufacturing process improvements to the i-stat 1 System, it is necessary to update standardization values from time to time to maintain long-term consistency of performance. Why Do i-stat 1 Analyzers Need Software Updates? The i-stat 1 System is designed to eliminate operator influence on delivered results. This process should take less than 10 minutes for the first i-stat 1 analyzer, and less time for additional i-stat 1 analyzers. 1 Instructions for Updating i-stat 1 Software Overview These instructions have been created specifically to guide you through the process of updating the software on your i-stat 1 analyzer(s).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |